2313k-manufacture,factory,supplier from China

Annealing, also known as simmering, code name Th, is the process of heating a steel piece to Ac1 or Ac3 or above (30-50 ℃), holding it for a period of time, and then slowly cooling it (usually using furnace cooling).Normalization, also known as open flame, code Z, is the process of heating steel parts to Ac3 or Acm or above (30-50 ℃), holding them for a period of time, and then cooling them in air at a slightly faster cooling rate than annealing.The main difference between bearing annealing and normalizing is that normalizing is a deformation or special case of complete annealing, and the only

（1） Linear bearing cages can be divided into stamped and solid types:a. Stamping cage: commonly made of steel plate, sometimes also made of copper plate. The advantage of this type of cage over metal solid cages is its lighter weight. The stamping cage occupies a small gap between the inner and outer rings of the linear bearing, making it easy for lubricating oil to enter the linear bearing and remain in the cage. According to the code principle, the stamping cage is only written into the code when it is not used as a standard structure.b.

After the opening ceremony, Zhou Yu, Chairman of the China Bearing Industry Association, accompanied leaders and guests such as Tang Jun, Director of the General Machinery Department of the Equipment Department of the Ministry of Industry and Information Technology, and Song Zhiming, former Deputy Director of the Planning Department of the Ministry of Industry and Information Technology, to visit the exhibition and exchange ideas with major exhibitors. During the exhibition, the China Bearing Industry Association, the China Petroleum and Petrochemical Equipment Association Industry Associ

In Shanghai,the 2023PTC exhibition was held as scheduled.On October 24-27, the 2023 Asia International Power Transmission and Control Technology Exhibition (PTC ASIA) opened grandly at the Shanghai New International Expo Center. This exhibition highlights the theme of "digital intelligence empowerment, innovation and upgrading", with an exhibition area of nearly 100000 square meters, attracting over 1500 enterprises from multiple countries and regions such as Germany and Italy to participate. As a leading enterprise in the Chinese bearing industry, Renben，TIMKEN,etc.

The so-called burn damage state of  bearings refers to the rapid heating of the raceway wheel, rolling element, and retainer of  bearings during rotation until discoloration, softening, deposition, and damage occur.The main reason for bearing burns is due to poor lubrication of  bearings, which may have used non-standard lubricants or excessive or insufficient lubricants, both of which are incorrect. Secondly, it may be due to excessive load (excessive preloading). The rotational speed is too high. The clearance is too small. There is water or other foreign objects invading.

As an efficient transmission product that converts the rotational motion of the motor into the linear feed motion of the nut, the selection of ball screw accuracy and assembly form has a significant impact on the accuracy assurance, speed assurance, and operating life of the system in practical use.

The linear module affects the operation of many mechanical devices and is also one of the basic elements of the machine. Therefore, the quality of the linear module has a great influence on the operation of the machine. So how can you check the quality of a linear module?

When replacing peripheral parts of the device, carry out regular maintenance, operational checks and inspections of the removed bearings to determine whether they can be reused and whether they are in good or bad condition.First, carefully examine and note the removed bearings and their appearance. To clarify and check the amount of residual grease, the bearings must be thoroughly cleaned&nbs

The exhibition, PTC ASIA 2024, will be held grandly at the Shanghai New International Expo Center from November 5th to 8th. As a benchmark for the power transmission industry in the Asia Pacific region, the exhibition is themed "Intelligent, Green, and High Quality Development" and will continue to bring innovative products and solutions to the industry.

The high-temperature bearing needs to be replaced and new high-temperature lubricating grease needs to be added. However, this lubricating grease needs to be added just right, whether it's too much or too little won't work. How much does it need to be added specifically?What is the problem with adding too much lubricating grease to high-temperature bearings?Adding too much high-temperature lubricating grease can cause damage to the bearings.(1) Adding too much lubricating grease will increase the friction torque.