HGW45HC Sliders-manufacture,factory,supplier from China

To successfully obtain valuable lunar soil, a series of key core technologies such as surface sampling and drilling are essential. Among them, surface sampling refers to using a robotic arm to carry a sampling device to shovel lunar soil or pick up lunar rocks at multiple positions on the lunar surface; Drilling is the process of using a drill rod to drill into the lunar surface at a predetermined depth and collect lunar soil core samples that maintain the "profile sequence".

The high-temperature bearing needs to be replaced and new high-temperature lubricating grease needs to be added. However, this lubricating grease needs to be added just right, whether it's too much or too little won't work. How much does it need to be added specifically?What is the problem with adding too much lubricating grease to high-temperature bearings?Adding too much high-temperature lubricating grease can cause damage to the bearings.(1) Adding too much lubricating grease will increase the friction torque.

The exhibition, PTC ASIA 2024, will be held grandly at the Shanghai New International Expo Center from November 5th to 8th. As a benchmark for the power transmission industry in the Asia Pacific region, the exhibition is themed "Intelligent, Green, and High Quality Development" and will continue to bring innovative products and solutions to the industry.

Bearings are crucial components for maintaining the normal operation of the vibrating screen. During normal operation, bearings should run smoothly and without any noise. However, due to poor quality or improper operation of the vibrating screen, bearings are prone to overheating, causing wear and even fracture, which seriously affects the normal use of the vibrating screen.1.Insufficient lubricationDuring the use of bearings, the internal lubricating oil is gradually consumed.

In modern industrial production, the performance of bearings directly affects the efficiency and lifespan of equipment. Especially in high load and high-speed applications, FAG bearings are widely used due to their excellent design and manufacturing processes. However, various industries also face a series of pain points when using FAG bearings, which often lead to reduced production efficiency, frequent equipment failures, and even affect the stability of the entire production line.

Annealing, also known as simmering, code name Th, is the process of heating a steel piece to Ac1 or Ac3 or above (30-50 ℃), holding it for a period of time, and then slowly cooling it (usually using furnace cooling).Normalization, also known as open flame, code Z, is the process of heating steel parts to Ac3 or Acm or above (30-50 ℃), holding them for a period of time, and then cooling them in air at a slightly faster cooling rate than annealing.The main difference between bearing annealing and normalizing is that normalizing is a deformation or special case of complete annealing, and the only

1. How to distinguish between heavy bearings and light bearingsActually, these differences are very obvious. Firstly, there is a difference in quality, which is mainly caused by two differences. The first difference is that in many cases, the material of lightweight bearings is different from that of heavy-duty bearings. You must understand this. In order to meet different industrial production or processing needs, bearings must have different performance. The different materials of various bearings are actually due to this reason.Another point is the difference in physical structure.

    On 15-18 May ,our company will participate 28th international machine tools,metalworking&automation machine tools,metalworking & automation technology exhibition in KUALA LUMPUR.     Welcome to our booth!    Booth number:3392Opening Hours:15-17 May (Wed-Fri.):10am-6pm18 May(Sat)               :10am-4pm

In Shanghai,the 2023PTC exhibition was held as scheduled.On October 24-27, the 2023 Asia International Power Transmission and Control Technology Exhibition (PTC ASIA) opened grandly at the Shanghai New International Expo Center. This exhibition highlights the theme of "digital intelligence empowerment, innovation and upgrading", with an exhibition area of nearly 100000 square meters, attracting over 1500 enterprises from multiple countries and regions such as Germany and Italy to participate. As a leading enterprise in the Chinese bearing industry, Renben，TIMKEN,etc.

From September 30 to October 5, 2024, Türkiye Machine Tool Exhibition will be held in Istanbul as scheduled. During the exhibition, we received business cards from customers from Türkiye, Iran, Russia and many other countries, felt the enthusiasm of visitors and recognition of our products, and looked forward to cooperating with them.